HPE2-T37 Using HPE OneView Questions and Answers

This volume is presented to the server.

This volume is marked as permanent.

This volume has at least one snapshot created.

This volume is rebuilding after the drive failure.

Baseboard Management Controller (BMC)

Rack Management Controller (RMC)

all nPARs created within the complex

only the base chassis from the complex

It supports HPE OneView instances from version 8.40 or newer.

It can be used tree of charge for the HPE Synergy platform because the licenses are included.

It is available for customers that have more than three HPE Synergy Frames.

It supports HPE ProLiant G6 and newer systems regardless of the OS installed.

Untagged

Internal

Tunnel

Tagged

You tried to add additional connection above the limit

The server is powered on

The server does not have an HPE OneView license applied

The server is powered off

to provide static IP addresses to IL0 and interconnect modules if applicable

to provide static IP addresses for an operating system running on a Compute Module

to provide static IP addresses for Logical Interconnects and Logical Enclosures

to provide static IP addresses for storage systems managed in HPE OneView

The sFlow option must be enabled and configured.

Both FlexNlCs must be connected to the same network.

The Compute Module profile must have exactly two connections defined.

An upgrade license must be purchased and deployed.

HPE One View Global Dashboard license

HPE OneView Advanced license

HPE composer 2 license

HPE OneView standard license

A logical JBOD lifecycle can be associated with a server profile lifecycle and drives can be securely erased.

A logical JBOD cannot be created during server profile creation and must be prepared in advance

Different types of the drives can be used within a logical JBOD as long as they have the same capacity

Logical JBOD functionality must be enabled on the Enclosure Group level by a storage administrator

The HPE OneView certificate from the primary site must be added to HPE OneView in the remote site.

The IP address assigned to HPE Composer installed in a remote site must be registered in a primary site.

Multi-site licenses must be added to HPE OneView and activate for all available HPE Synergy frames.

Management ports of the remote frame link topology must be connected to the management LAN.

Enable VMware Fault Tolerance if the appliance is deployed to a VMware hypervisor.

deploy the appliance in a hypervisor cluster that Is not managed by OneView.

Use thin-provisioning for the HPE OneView appliance to save storage capacity.

Deploy two HPE OneView appliances and configure them in HA mode.

This mode will suppress unwanted emails and activity alerts for routine server maintenance.

This mode will temporarily remove server profiles from the server for the maintenance period.

This mode will disable all network and storage connections during the maintenance period.

This mode will position the server in an isolated network to allow hardware or software maintenance.

It is deployed as an agent on any supported and managed array.

It |i deployed as a virtual appliance to the supported hypervisor.

It is the part of the standard HPE OneView appliance, but it must be activated.

It is deployed as an application on Windows system running in the virtual machine.

It is a collection of all internal networks defined for a specific type of traffic like vSAN or vMotion.

It is a collection of untagged Ethernet networks that form a named group to simplify server profile creation.

It is a collection of tagged Ethernet networks that form a named group to simplify server profile creation.

It is a collection of all networks configured within HPE OneView regardless of network type.

For FC uplink sets, an additional uplink from second module should be added for redundancy.

The maximum supported number of the internal networks for logical interconnect is configured.

Additional uplink ports can be added to ETH-Uplink to increase available bandwidth.

FC uplinks are not supported and will be converted to FCoE or RoCE uplinks.

Remote HPE Synergy setup is possible if HPE Composer 2 is used and a DHCP server Is available in the management network.

Remote HPE Synergy Installation can be done only if an additional set of the services was purchased together with hardware platform.

HPE Synergy cannot be deployed remotely, as Initial setup must be performed using a local console connection.

HPE Synergy can be configured remotely through a secure connection to the FLM if this option was enabled In the factory.

A server profile can be created only for HPE BladeSystem, HPE Synergy, and HPE Superdome Flex servers.

A server profile created for a specific server hardware type cannot be moved to a server with a different server hardware type.

A server profile can be used to configure a local storage controller, but cannot be used to configure SAN-based storage.

A server profile can be used to update firmware and drivers when the operating system on the server is up and running.

Fibre Channel connections can be defined

UEFI optimized is the only available boot mode

Virtual WWNs and MAC addresses can be defined

Enclosure Group Is automatically selected

Compute Module

Storage Array

Master Module

Logical Enclosure

HPE Remote Support

Active Directory integration

Security mode

Trap destination to HPE OneView

partition layout for servers running Linux.

IL0 IPv4 or IPv6 address.

local storage and BIOS settings.

NIC teaming setup at OS level.

network and storage connectivity.

Only HPE Synergy Compute Modules with a server profile applied.

Any Gen8, Gen9 and Gen10 servers managed using HPE OneView.

Any servers under warranty or active service contract.

Any server except HPE Superdome Flex and HPE Superdome Flex 280.

A logical enclosure can have between 1 to 5 HPE BladeSystem c7000 enclosures.

A logical enclosure must be created only for monitored HPE BladeSystem C700O enclosures.

A logical enclosure is created automatically, and it is always based on a single enclosure.

A logical enclosure can contain a mix of HPE BladeSystem c7000 and C3000 enclosures.

Source system has to be placed in a maintenance mode.

Target system must be powered off.

Source server has to be powered on.

Target server has to be placed in a maintenance mode.

Visualization of MACs and WWNs.

Storage connection management

SAN storage management.

Firmware and drivers update options.

A PowerShell script must be used to upload IL0 firmware to the Internal or external firmware repository.

A custom SPP iso Image must be created with the new IL0 firmware version and uploaded to the repository.

An external repository must be created, because standalone components are supported only In an external repository.

ILO firmware can be marked as a hotnx and uploaded directly to the Internal or external firmware repository.

Volumes created on the first storage pool cannot use data reduction technologies

Both storage pools are in a managed state and can be used for volume provisioning

HPE OneView can be used to configure volume replication between these pools

Both storage pools have a license applied that enables management of these pools

The WSAPI and VASA provider are enabled on the array.

The CPG was imported as a managed storage pool.

The array has a proper license in HPE oneView.

The array is enabled for HPE OneView management.

A server profile template must be created.

All memory installed must be the maximum size.

An appropriate HPE OneView license is required.

A second processor must be installed.

When the appliance is offline, it may affect network or storage traffic.

When the appliance is offline, all servers are placed in maintenance mode.

When the appliance is offline, it does not affect the managed resources.

When the appliance is offline, the iL0 processor is not accessible.

Boot volumes can be created on demand and defined in the server profile template.

Boot volumes can be prepared in advance and later presented as shared volumes to the Compute Modules.

An existing volume can be replicated automatically when creating a server profile.

single SAN volume can be created and utilized by all HPE Synergy Compute Modules.